1/20/2024 0 Comments Errors in project validation idvdThey apparently have fewer layers in the composition of the disk. Memorex and TDK are not consistent and may not give you a correct burn. Recommended brands here are Verbatim, Maxell and Taio Yuden. Also, many of us have experienced fewer problems on playback with DVD-R disks. Second, you should use a better brand of DVD disk. external USB/USB2 hard disks, other FW hard disks etc.ģ Chapter marks in transitions - minimum 2 sec fromįirst, I do not think that mixing wide-screen and standard makes a difference in iDVD. Disconnect any other external devices not absolutely needed.Į.g. I made several additional copies using Disc Utility. A long and tortuous process, but at last something works. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. Be sure to click the DVD DL drive in the window "Burn disc in.". So then I tried Utilities> Disc Utility> Burn icon, and followed it through. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. One of the replies on a thread with this subject said not to, but my experience today is good. Apple tech support's tip was to try disc image. Apple tech support really didn't know what to do but gave me a very good tip. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. I always makes a DiskImage first and test this so that it runs OK Simply remember to add subtitles to your Quicktime files and menu buttons.ĭo a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears). Important when from iMovie HD6 or previous - Now also observed when using FCE 4 Not in a transition (or within 2-3 seconds from it).Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self.I renamed it without the symbol and low and behold, it worked. I had a project that had a + sign which caused the same problem. If so, that is why you are getting the error. Does the title of your project have any symbols or decimal points in it. keep to a-z and 0-9 strange letters in project name e.g. Using strange letters in video project name e.g. aiff (as on audio-CDs) (else converted to this. Video - StreamingDV (miniDV tape via FireWire) andĪudio. Use of strange video/audio material e.g.avi. Use high quality brand of DVD - I only use Verbatim DVD-R (others may have luck by use of other DVDs)Įlse read my long note of collected thoughts on this. can also trigger this most often symbols other than letters.Ĭ. Use of other letters than a to z and 0 to 9 in Titles and or Chapter names etc. Turn on - in iDVD - TV-Safe area and see if anything's goes outside this OR EVEN Touching it - Move all buttons etc. Always use top quality media: Verbatim, Maxell or Taiyo Yuden DVD-R are the most recommended in these forums.Yes - Multiplexing Error - is confusing and there are many various things that can trigger it.Ī. Then burn to disk with Disk Utility or Toast at the slowest speed available (2x-4x) to assure the best burn quality. If it plays OK with DVD Player the encoding is good. To check the encoding mount the disk image, launch DVD Player and play it. This will separate the encoding process from the burn process. Once you have the project as you want it save it as a disk image via the File ➙ Save as Disk Image menu option. The part of my post he was referring to in the link he provided is somewhat lost in my long winded post so here is it again:įollow this workflow to help assure the best qualty video DVD: You can click on Find File and locate the file on your HD (difficult if it's in an iPhoto LIbrary) or do as J Keller suggests and create a new project. if you get this window you have broken links.close iDVD and then reopen the project.Try the following to determine if you have broken links and try to fix them:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |